62 Facts Regarding Ac Vent Temperature Measurement

This time, we’re going to talk about How To Measure Ac Vent Temperature. There is a lot of information about How To Measure Ac Temperature on the internet, of course. Social media are getting better and better quickly, which makes it easier for us to learn new things.

Heating, ventilation, and air conditioning and Ac Blowing 70 Degree Air are also linked to information about Heating, ventilation, and air conditioning. As for other things that need to be looked up, they are about Ac Blowing 70 Degree Air and have something to do with Window Air Conditioner Air Temperature Output.

62 Things About How To Measure Ac Vent Temperature | Ac Vent Temperature Chart

• Now that you know your filters are clean, here’s how to test your AC temperature. You’ll want to do this test on a day when the outside temperature is above 80 degrees F. Follow these steps in order to check if your AC is working properly: - Source: Internet
• In other words, if the air temperature in your house is 78 degrees, then you would expect the air coming out of the vents to be between 58 and 63 degrees. Don’t worry if the air isn’t exactly in this range, but it should be close. Any cooling differential of less than 10-12 degrees could indicate a problem. - Source: Internet
• First, be sure you have replaced your furnace filter and then remove your vent covers prior to testing. This way you can rule out anything that would be restricting air flow as the cause for any problems. For loose fitting vents you should be able to easily pop them off. If they are fitted snug, you might need a tool to pry them off. Perhaps a flat head screwdriver or pliers. - Source: Internet
• Energy efficiency can be improved even more in central heating systems by introducing zoned heating. This allows a more granular application of heat, similar to non-central heating systems. Zones are controlled by multiple thermostats. In water heating systems the thermostats control zone valves, and in forced air systems they control zone dampers inside the vents which selectively block the flow of air. In this case, the control system is very critical to maintaining a proper temperature. - Source: Internet
• With the split system, the evaporator coil is connected to a remote condenser unit using refrigerant piping between an indoor and outdoor unit instead of ducting air directly from the outdoor unit. Indoor units with directional vents mount onto walls, suspended from ceilings, or fit into the ceiling. Other indoor units mount inside the ceiling cavity so that short lengths of duct handle air from the indoor unit to vents or diffusers around the rooms. - Source: Internet
• In modern buildings, the design, installation, and control systems of these functions are integrated into one or more HVAC systems. For very small buildings, contractors normally estimate the capacity and type of system needed and then design the system, selecting the appropriate refrigerant and various components needed. For larger buildings, building service designers, mechanical engineers, or building services engineers analyze, design, and specify the HVAC systems. Specialty mechanical contractors and suppliers then fabricate, install and commission the systems. Building permits and code-compliance inspections of the installations are normally required for all sizes of buildings. - Source: Internet
• Because an air conditioner moves heat between the indoor coil and the outdoor coil, both must be kept clean. This means that, in addition to replacing the air filter at the evaporator coil, it is also necessary to regularly clean the condenser coil. Failure to keep the condenser clean will eventually result in harm to the compressor because the condenser coil is responsible for discharging both the indoor heat (as picked up by the evaporator) and the heat generated by the electric motor driving the compressor. - Source: Internet
• Supply vents : These are the vents that blow air into each room. The conditioned air goes from your air conditioner or furnace, travels through the ductwork and exits out the supply vents. These vents are easy to identify, as they’re the only vents from which you can feel conditioned air blowing out. - Source: Internet
• The use of furnaces, space heaters, and boilers as a method of indoor heating could result in incomplete combustion and the emission of carbon monoxide, nitrogen oxides, formaldehyde, volatile organic compounds, and other combustion byproducts. Incomplete combustion occurs when there is insufficient oxygen; the inputs are fuels containing various contaminants and the outputs are harmful byproducts, most dangerously carbon monoxide, which is a tasteless and odorless gas with serious adverse health effects.[16] - Source: Internet
• Natural ventilation is the ventilation of a building with outside air without using fans or other mechanical systems. It can be via operable windows, louvers, or trickle vents when spaces are small and the architecture permits. ASHRAE defined Natural ventilation as the flow of air through open windows, doors, grilles, and other planned building envelope penetrations, and as being driven by natural and/or artificially produced pressure differentials.[2] - Source: Internet
• Running your air conditioner is probably the most expensive part of your household utility bill. The bigger the house, the more area you have to cool. In addition to having energy efficient features installed in your home, it helps to know how to check if your AC is running properly. Knowing how to test your AC temperature will help you determine when to have it serviced. - Source: Internet
• Although HVAC is executed in individual buildings or other enclosed spaces (like NORAD’s underground headquarters), the equipment involved is in some cases an extension of a larger district heating (DH) or district cooling (DC) network, or a combined DHC network. In such cases, the operating and maintenance aspects are simplified and metering becomes necessary to bill for the energy that is consumed, and in some cases energy that is returned to the larger system. For example, at a given time one building may be utilizing chilled water for air conditioning and the warm water it returns may be used in another building for heating, or for the overall heating-portion of the DHC network (likely with energy added to boost the temperature).[4][5][6] - Source: Internet
• The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI (Heating, Air-conditioning and Refrigeration Distributors International), ASHRAE, SMACNA, ACCA (Air Conditioning Contractors of America), Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement. (UL as an omnibus agency is not specific to the HVAC industry.) - Source: Internet
• Each volume of the ASHRAE Handbook is updated every four years. The Fundamentals Handbook includes heating and cooling calculations. The design professional must consult ASHRAE data for the standards of design and care as the typical building codes provide little to no information on HVAC design practices; codes such as the UMC and IMC do include much detail on installation requirements, however. Other useful reference materials include items from SMACNA, ACGIH, and technical trade journals. - Source: Internet
• HVAC is based on inventions and discoveries made by Nikolay Lvov, Michael Faraday, Rolla C. Carpenter, Willis Carrier, Edwin Ruud, Reuben Trane, James Joule, William Rankine, Sadi Carnot, and many others.[12] - Source: Internet
• Dougflas on Sat July 01, 2006 11:52 AM Measuring air temps takes some precautions. IR thermometers depend upon the color of the material you’re trying to measure and you must keep this in mind. shiny metals mearured will not be accurate due to the emmeasibility of the meatal. I use the IR when checking the inout and output of the evaps. I don’t care to an extent what it reads as long a the readings are close to each other as long as the evap tubes are equally colorized. - Source: Internet
• The heat pump gained popularity in the 1950s in Japan and the United States.[14] Heat pumps can extract heat from various sources, such as environmental air, exhaust air from a building, or from the ground. Heat pumps transfer heat from outside the structure into the air inside. Initially, heat pump HVAC systems were only used in moderate climates, but with improvements in low temperature operation and reduced loads due to more efficient homes, they are increasing in popularity in cooler climates, they can also operate in reverse by cooling an interior. - Source: Internet
• Air cleaning and filtration removes particles, contaminants, vapors and gases from the air. The filtered and cleaned air then is used in heating, ventilation, and air conditioning. Air cleaning and filtration should be taken in account when protecting our building environments.[34] - Source: Internet
• Chick on Fri June 30, 2006 7:47 PM Yes, what you have to do is put it on the vent, wait a couple seconds and hit it…then it will read the vent temp and blink between scanning and just stop there. other wise it will keep dropping. I guess the best way would be a couple inches away or even as far as six. it take a little practice with those.. - Source: Internet
• Before checking the temperature itself, be sure to check your air filters. When air filters are clogged, your air conditioning won’t work efficiently because less air coming through the filter means less air is getting cooled. If this happens, it can also lead to the evaporator coils accumulating frost, causing the system to overheat. - Source: Internet
• Kitchens and bathrooms typically have mechanical exhausts to control odors and sometimes humidity. Factors in the design of such systems include the flow rate (which is a function of the fan speed and exhaust vent size) and noise level. Direct drive fans are available for many applications and can reduce maintenance needs. - Source: Internet
• ISO 16813:2006 is one of the ISO building environment standards.[35] It establishes the general principles of building environment design. It takes into account the need to provide a healthy indoor environment for the occupants as well as the need to protect the environment for future generations and promote collaboration among the various parties involved in building environmental design for sustainability. ISO16813 is applicable to new construction and the retrofit of existing buildings.[36] - Source: Internet
• A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements that have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building. - Source: Internet
• The best way is to use a “stick” or get a thermocouple type. I found a thermocouple with a digital display at Walmart one day for 5 bucks or so in the automotive section.Yeah, I probably am just going to buy one of those. I really like Infrared thermometers, but they aren’t very good at measuring air temperature. Measuring the temperature across the condenser or trying to find a hot spot on an engine part, now that is where the infrared thermometer shines. - Source: Internet
• at the air intake. This is where the air is pulled into your air conditioning system to be cooled. You don’t want to simply take the temperature at the thermostat or elsewhere in the house because it is possible that the temp with vary from place to place in the house and give an inaccurate reading to how much the air is actually being cooled. - Source: Internet
• Heaters exist for various types of fuel, including solid fuels, liquids, and gases. Another type of heat source is electricity, normally heating ribbons composed of high resistance wire (see Nichrome). This principle is also used for baseboard heaters and portable heaters. Electrical heaters are often used as backup or supplemental heat for heat pump systems. - Source: Internet
• Demand controlled kitchen ventilation (DCKV) is a building controls approach to controlling the volume of kitchen exhaust and supply air in response to the actual cooking loads in a commercial kitchen. Traditional commercial kitchen ventilation systems operate at 100% fan speed independent of the volume of cooking activity and DCKV technology changes that to provide significant fan energy and conditioned air savings. By deploying smart sensing technology, both the exhaust and supply fans can be controlled to capitalize on the affinity laws for motor energy savings, reduce makeup air heating and cooling energy, increasing safety, and reducing ambient kitchen noise levels.[33] - Source: Internet
• Next, you want to take the temperature of the air coming out of the vents. Simply point your thermometer into the vents to take the reading. If you have central air conditioning with ducts that run through the attic then you will likely notice a variance in temperature from vents that are close to the indoor air conditioning unit (sometimes located in a closet or sometimes in the attic as well) and those that are farther away. - Source: Internet
• Best just to charge with R-134a to 90% of what the R-12 label calls for and make sure your pressures are in the ballpark for the current ambient and RH conditions. Another indication is when the outlet evaporator temperature approaches the inlet temperature, but again watching pressures. On some conversions, maximum pressures are reached when you still have foam feeding the evaporator and foam doesn’t carry away very much heat, you can feel this foam with a delicate touch on the inlet, but this tells you something has to be done with the condenser like adding fans to it or converting it to a parallel flow. - Source: Internet
• The three major functions of heating, ventilation, and air conditioning are interrelated, especially with the need to provide thermal comfort and acceptable indoor air quality within reasonable installation, operation, and maintenance costs. HVAC systems can be used in both domestic and commercial environments. HVAC systems can provide ventilation, and maintain pressure relationships between spaces. The means of air delivery and removal from spaces is known as room air distribution.[3] - Source: Internet
• In general, with ambient air temperatures 70ş degrees Fahrenheit and humidity 20 %, the evaporator outlet air temperature should be in the 35ş-40ş degrees Fahrenheit range. On the other extreme of 80ş degrees Fahrenheit ambient air temperature and 90 % humidity condition, the evaporator air outlet temperature might be in the 45ş to 50ş degrees Fahrenheit range. That’s a temperature differential of 30ş-35ş degrees Fahrenheit. Because of all these variations, it is difficult to pinpoint what evaporator outlet air temperature should be on all applications; a good idea is to compare the readings obtained to manufacturer’s specifications. - Source: Internet
• Heating, ventilation, and air conditioning (HVAC)[1] is the use of various technologies to control the temperature, humidity, and purity of the air in an enclosed space. Its goal is to provide thermal comfort and acceptable indoor air quality. HVAC system design is a subdiscipline of mechanical engineering, based on the principles of thermodynamics, fluid mechanics, and heat transfer. “Refrigeration” is sometimes added to the field’s abbreviation as HVAC&R or HVACR, or “ventilation” is dropped, as in HACR (as in the designation of HACR-rated circuit breakers). - Source: Internet
• Homes constructed before the advent of central air often have retrofitted HVAC systems. The earliest HVAC systems featured a large, single return vent placed somewhere in the middle of the home, but this is not the most effective system. Instead, there should be at least one return vent in every room, with two or three being ideal. - Source: Internet
• If you use a digital thermometer with the K type thermocouple to measure the air, your reading will not be accuraqte. athese ak types are for contact use only…tape ot wire tie the end of the pick up to the surface tightly and insulate from the ambient. so even sticking the end in the vents will not be accurate. It’ll get you in the ballpark. - Source: Internet
• Within the construction sector, it is the job of the building services engineer to design and oversee the installation and maintenance of the essential services such as gas, electricity, water, heating and lighting, as well as many others. These all help to make buildings comfortable and healthy places to live and work in. Building Services is part of a sector that has over 51,000 businesses and employs represents 2%-3% of the GDP. - Source: Internet
• If during your tests you find that you aren’t meeting the 15-20 degree differential, then it’s best to have a professional come check your system. The number of potential issues can range from low refrigerant to not enough insulation to dirty coils that cause inefficient cooling. The good news is that most experienced HVAC (heating, ventilation, air conditioning) technicians can pinpoint the problem quickly and get you back to blowing cold air. - Source: Internet
• In variable climates, the system may include a reversing valve that switches from heating in winter to cooling in summer. By reversing the flow of refrigerant, the heat pump refrigeration cycle is changed from cooling to heating or vice versa. This allows a facility to be heated and cooled by a single piece of equipment by the same means, and with the same hardware. - Source: Internet
• If during your readings you find that there are major differences in the air coming out of the vents (differences of 5-10 degrees or more), there are any number of issues it could be. Most likely, however, it has to do with your ducting that funnels the air from the air conditioner to the vent. Many times the insulation on the ducts can be ripped or torn or simply too thin. This allows the heat from the attic to warm the air inside the duct. - Source: Internet
• Ventilating or ventilation (the “V” in HVAC) is the process of exchanging or replacing air in any space to provide high indoor air quality which involves temperature control, oxygen replenishment, and removal of moisture, odors, smoke, heat, dust, airborne bacteria, carbon dioxide, and other gases. Ventilation removes unpleasant smells and excessive moisture, introduces outside air, keeps interior building air circulating, and prevents stagnation of the interior air. Methods for ventilating a building are divided into mechanical/forced and natural types.[2] - Source: Internet
• All modern air conditioning systems, even small window package units, are equipped with internal air filters. These are generally of a lightweight gauze-like material, and must be replaced or washed as conditions warrant. For example, a building in a high dust environment, or a home with furry pets, will need to have the filters changed more often than buildings without these dirt loads. Failure to replace these filters as needed will contribute to a lower heat exchange rate, resulting in wasted energy, shortened equipment life, and higher energy bills; low air flow can result in iced-over evaporator coils, which can completely stop airflow. Additionally, very dirty or plugged filters can cause overheating during a heating cycle, which can result in damage to the system or even fire. - Source: Internet
• The next thing you will need to do is determine which ducts in your house are the return ducts and which are the supplies. To do this place a tissue over each duct in your house. When you place a tissue over a supply vent it will blow the tissue away from the duct. When you place the tissue over the return duct it will suck the tissue into it. After you’ve determined which of your ducts are returns and which are supplies you can began the test. - Source: Internet
• NickD on Sat July 01, 2006 9:20 AM Vent temps are secondary to pressure readings, in theory and even sometimes in practice, vent temps will decrease while charge is added starting from zero charge. A point is reached where the system is full and the charge overfill will begin to fill up either the receiver or the accumulator, at this point, adding more charge will not decrease the vent temperatures but will stabilize. Adding even more will increase vent temps and even blow up the system. Vent temps can throw you off if you are using them as the main basis of charging as you may only optimize your charge for a given ambient temperature and RH factor, system may blow up at higher temperatures or cycle to rapidly at lower temperatures. - Source: Internet
• NickD on Fri June 30, 2006 9:42 PM According to the old books on this subject, only one center vent should be opened, with the blower at max to measure vent temperature by sticking a stick thermometer into the vent. IR can’t measure air, only surfaces and these are typically plastic surfaces, different colored surfaces will show vastly different temperatures unless your IR thermometer has compensation for this. Plus, it takes time to cool the plastic and depending on what is behind that plastic, like a red hot CD player, results won’t be accurate. - Source: Internet
• An HVAC technician is a tradesman who specializes in heating, ventilation, air conditioning, and refrigeration. HVAC technicians in the US can receive training through formal training institutions, where most earn associate degrees. Training for HVAC technicians includes classroom lectures and hands-on tasks, and can be followed by an apprenticeship wherein the recent graduate works alongside a professional HVAC technician for a temporary period.[citation needed] HVAC techs who have been trained can also be certified in areas such as air conditioning, heat pumps, gas heating, and commercial refrigeration. - Source: Internet
• Mechanical, or forced, ventilation is provided by an air handler (AHU) and used to control indoor air quality. Excess humidity, odors, and contaminants can often be controlled via dilution or replacement with outside air. However, in humid climates more energy is required to remove excess moisture from ventilation air. - Source: Internet
• JJM on Sat July 01, 2006 1:06 PM Keep in mind, infrared thermometers measure surface temperatures, they’re really not good at measuring at temperatures. They’re also subject to “thermal shock” so if you keep it front of the vent too long, it will absorb the cold and give incorrect temperatures. The more expensive ones are less sensitive to it, but still can be affected nonetheless. - Source: Internet
• Dehumidification (air drying) in an air conditioning system is provided by the evaporator. Since the evaporator operates at a temperature below the dew point, moisture in the air condenses on the evaporator coil tubes. This moisture is collected at the bottom of the evaporator in a pan and removed by piping to a central drain or onto the ground outside. - Source: Internet
• Multiple inventions within this time frame preceded the beginnings of the first comfort air conditioning system, which was designed in 1902 by Alfred Wolff (Cooper, 2003) for the New York Stock Exchange, while Willis Carrier equipped the Sacketts-Wilhems Printing Company with the process AC unit the same year. Coyne College was the first school to offer HVAC training in 1899.[13] - Source: Internet
• Keeping air filters clean and free of debris is always the first and easiest step to maintaining your air conditioning system at optimal performance. In fact, a clogged filter is one of the primary reasons for complete system shutdown. Replace filters regularly. - Source: Internet
• Obtain a temperature probe: This device will provide a quick and accurate measurement of the surrounding air temperature. Record the return vent temperature: Take your temperature probe and record the return vent’s temperature. Record supply vent temperatures: Go to three supply vents and measure their temperatures. Determine the supply vent average temperature: Add the three recorded temperatures together and divide by three to get the average temperature of the supply vents. Determine Delta T: To figure out Delta T, subtract the temperature of the return air from the average temperature of the supply vents. - Source: Internet
• Ventilation is the process of changing or replacing air in any space to control the temperature or remove any combination of moisture, odors, smoke, heat, dust, airborne bacteria, or carbon dioxide, and to replenish oxygen. Ventilation often refers to the intentional delivery of the outside air to the building indoor space. It is one of the most important factors for maintaining acceptable indoor air quality in buildings. Methods for ventilating a building may be divided into mechanical/forced and natural types.[18] - Source: Internet
• If your house has only one return vent, this is not a problem — make sure to keep the doors open in every room so the air can circulate properly. Make sure there are no furniture, draperies, rugs, etc. blocking return vents. If you ever need to replace portions of the ducts in your home, this may be a good opportunity to install a few additional return vents. - Source: Internet
• Free cooling systems can have very high efficiencies, and are sometimes combined with seasonal thermal energy storage so that the cold of winter can be used for summer air conditioning. Common storage mediums are deep aquifers or a natural underground rock mass accessed via a cluster of small-diameter, heat-exchanger-equipped boreholes. Some systems with small storages are hybrids, using free cooling early in the cooling season, and later employing a heat pump to chill the circulation coming from the storage. The heat pump is added-in because the storage acts as a heat sink when the system is in cooling (as opposed to charging) mode, causing the temperature to gradually increase during the cooling season. - Source: Internet
• This measurement can be made with an inexpensive thermometer and a manifold pressure gauge set. Evaporator outlet temperature varies according to outside ambient air and humidity conditions. Further variations can be found, depending on wether the system is controlled by a cycling clutch compressor or an evaporator temperature sensor. The design of the hvac plenum ducts is another factor that we need to take into account while running an efficiency performance test. - Source: Internet
• Central, “all-air” air-conditioning systems (or package systems) with a combined outdoor condenser/evaporator unit are often installed in North American residences, offices, and public buildings, but are difficult to retrofit (install in a building that was not designed to receive it) because of the bulky air ducts required.[23] (Minisplit ductless systems are used in these situations.) Outside of North America, packaged systems are only used in limited applications involving large indoor space such as stadiums, theatres or exhibition halls. - Source: Internet
• So now that you have results, what’s this new information mean? On a properly running air conditioning system you should see a difference of 20 degrees between your supply and return air ducts. If the difference between your return to supply is less than 20 degrees your air conditioner could have a problem. If it does you could also be causing damage to your unit as it runs. It hard to say exactly what the problem would be without looking at it but a lot of the times at Neighborhood we find that the unit is low on refrigerant or needs a minor repair. - Source: Internet
• The control circuit in a household HVAC installation. The wires connecting to the blue terminal block on the upper-right of the board lead to the thermostat . The fan enclosure is directly behind the board, and the filters can be seen at the top. The safety interlock switch is at the bottom left. In the lower middle is the capacitor - Source: Internet
• In more complex schemes, warm air is allowed to rise and flow out high building openings to the outside (stack effect), causing cool outside air to be drawn into low building openings. Natural ventilation schemes can use very little energy, but care must be taken to ensure comfort. In warm or humid climates, maintaining thermal comfort solely via natural ventilation might not be possible. Air conditioning systems are used, either as backups or supplements. Air-side economizers also use outside air to condition spaces, but do so using fans, ducts, dampers, and control systems to introduce and distribute cool outdoor air when appropriate. - Source: Internet
• Hidden behind the walls of your home is a vast network of air ducts. They connect to virtually every room of your house and provide a pathway through which air can travel to and from your HVAC system. In this article, we’ll discuss the differences between supply and return vents and provide tips on how to maintain them. - Source: Internet
• A stem type thermometer, or DVM with a temperature probe is in my opinion the most accurate method to measure vent temps. But the most important measure is does the system keep YOU cool… that’s the most important. - Source: Internet
• Ventilation duct with outlet diffuser vent. These are installed throughout a building to move air in or out of rooms. In the middle is a damper to open and close the vent to allow more or less air to enter the space. - Source: Internet
• A thermometer is used to determine air discharge temperature coming out from the duct nozzle into the cabin compartment. On more humid days, operating pressures will be higher on the high side of the a/c system. On less humid days, the operating pressures will read lower on the low side of the a/c system. - Source: Internet

Here are a few tips to help you find information about Ac Vent Temperature Chart: - Look for good places to get information about Air Conditioner Temperature. This can be done in libraries, on websites, or even by paid journalists. - When looking for information about How To Measure Ac Temperature, it's important to know that there are different kinds of online sources, like Google and YouTube. Social media sites like Facebook and Twitter are also good places to look for information about Home Ac Temperature Chart.

Video | How To Measure Ac Vent Temperature

To get the best information about Air Conditioner Temperature, you should read to find out how true each source is.

This article has a few videos from different places about Ac Vents Blowing Different Temperatures that will help you learn more about it. The Internet is a great place to find out about a wide range of things.

## Here are some crucial points concerning What Temperature Should My Central Air Conditioner Be Putting Out? A PHX Tech Explains.:

• How To Measure Ac Vent Temperature
• What Temperature Should Air Be Coming Out Of Vent When Cooling
• Ac Vent Temperature Chart
• Ac Blowing 70 Degree Air
• How To Measure Ac Temperature

With so many websites and forums that talk about Home Ac Temperature Chart, it shouldn’t be hard to find what you need.

Most people are used to getting information about Ac Blowing 70 Degree Air in a very different way than this. It lets you look at the information about Home Ac Temperature Chart and how it can be used in more detail. ways to put information about Ac Vent Temperature Chart in a way that looks good and is useful. They can be used in business and marketing, and they can also be used to talk about How To Measure Ac Temperature. So, we also give you some pictures about Home Ac Temperature Chart.

In the end, this article gives a summary of Blog. Also talked about are Blog and Ac Vents Blowing Different Temperatures, which you can use to compare how much you know about Heating, ventilation, and air conditioning.